PIC18F83J11T-I/PT【PDF 74/332 页】IC PIC MCU FLASH 4KX16 80TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3871

70页 71页 72页 73页 [74页]75页 76页 77页 78页

2010 Microchip Technology Inc.

DS39774D-page 165

PIC18F85J11 FAMILY

15.0 TIMER3 MODULE

The Timer3 timer/counter module incorporates these

features:

Software selectable operation as a 16-bit timer or

counter

Readable and writable 8-bit registers (TMR3H

and TMR3L)

Selectable clock source (internal or external) with

device clock or Timer1 oscillator internal options

Interrupt on overflow

Module Reset on CCPx Special Event Trigger

A simplified block diagram of the Timer3 module is

shown in Figure 15-1. A block diagram of the module’s

operation in Read/Write mode is shown in Figure 15-2.

The Timer3 module is controlled through the T3CON

options for the CCP modules. See Section 16.2.2

“Timer1/Timer3

Mode

Selection”

for

information.

REGISTER 15-1:

T3CON: TIMER3 CONTROL REGISTER

R/W-0

RD16

T3CCP2

T3CKPS1

T3CKPS0

T3CCP1

T3SYNC

TMR3CS

TMR3ON

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

-n = Value at POR

‘1’ = Bit is set

‘0’ = Bit is cleared

x = Bit is unknown

bit 7

RD16: 16-Bit Read/Write Mode Enable bit

= Enables register read/write of Timer3 in one 16-bit operation

= Enables register read/write of Timer3 in two 8-bit operations

bit 6,3

T3CCP<2:1>: Timer3 and Timer1 to CCPx Enable bits

= Timer3 is the capture/compare clock source for the CCP modules

= Timer3 is the capture/compare clock source for CCP2;

Timer1 is the capture/compare clock source for CCP1

= Timer1 is the capture/compare clock source for the CCP modules

bit 5-4

T3CKPS<1:0>: Timer3 Input Clock Prescale Select bits

= 1:8 Prescale value

= 1:4 Prescale value

= 1:2 Prescale value

= 1:1 Prescale value

bit 2

T3SYNC: Timer3 External Clock Input Synchronization Control bit

(Not usable if the device clock comes from Timer1/Timer3.)

When TMR3CS = 1:

= Do not synchronize external clock input

= Synchronize external clock input

When TMR3CS = 0:

This bit is ignored. Timer3 uses the internal clock when TMR3CS = 0.

bit 1

TMR3CS: Timer3 Clock Source Select bit

= External clock input from Timer1 oscillator or T13CKI (on the rising edge after the first falling edge)

= Internal clock (FOSC/4)

bit 0

TMR3ON: Timer3 On bit

= Enables Timer3

= Stops Timer3

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式